How To Install Crown Molding Around Windows

Download Article

Download Article

Installing molding, whether you lot're installing crown molding or installing baseboard molding or anything in betwixt, uses the aforementioned bones techniques. You lot might accept to hire a couple of the tools needed for this job, such as a miter box and an air hammer with an air hose and compressor, only otherwise, this is a projection you may be able to tackle yourself!

1. 1

   Cut the pieces to the right size . Brand sure all of your pieces are cut to the correct size. Post-obit sections will give specific advice on how to do that if y'all haven't already.

2. 2

   Locate and mark your studs. It'southward all-time to nail molding into a stud (the internal, wooden back up structure in your walls). Discover and mark your studs using a stud finder or other alternative method.^[1]

   Advert

3. iii

   Glue the edges. When placing molding, y'all want to outset mucilage the edges that will be making contact with the wall or ceiling. Don't use besides much glue or become information technology too shut to the edge, as this tin can cause seepage.^[2]

4. 4

   Place the piece. One time y'all've added your glue, put the slice in places and adjust it until it fits snugly. Marking where on the wall the piece needs to line up, in pencil, tin can help a lot here. Utilise a wall light amplification by stimulated emission of radiation-level if your ceiling is uneven. You can employ a box cutter or other advisable tool to shave a bit off the meridian of your molding to accommodate dips in the ceiling.^[three]

   • If the piece is long, up high, and you lot don't have someone to give you a manus, just place a nail in the wall at the line where you know the lesser of the molding will be, roughly 1-2' from the end. You lot can patch this later.

5. v

   Nail it in place. With the molding fit into place, put a nail (add the thickness of the molding plus the drywall and a 1/2" for the stud to get the nail length) through the molding into the stud closest to the end of the piece. A nail gun will make this much easier. Try to nail the molding in merely at the studs or at frames (such as effectually a window or door), as nailing elsewhere can atomic number 82 to accidentally hitting a pipage or wiring!^[4]

   • Wait to nail in the last 1.5-2' of a piece until you've fit in the piece that goes next to it. This will assist you fit the pieces together more snugly.

6. half dozen

   Do finishing touches. Employ a nail setter to push in nails which are tool exposed.^[5] Use wall patching paste or forest putty to fill and mask the holes from the nails. Use caulk around the gaps between the molding and the wall. Caulking is especially important around doors and windows, to help gainsay moisture issues.^[6] Employ paint as necessary to hide repairs.

   Ad

Cutting Inside Corners Download Article

1. ane

   Measure your piece. Mensurate the distance between the final board end and the corner. Cut a slice of molding to this length. Mensurate and cut pieces for both sides of the corner.

2. two

   Miter the ends. Miter the ends of both corner pieces at a 45° bending, with the long signal on the dorsum side, where the molding volition bear upon the wall. This should let the two corner pieces to fit together.^[7]

   • The length on the backside should now be longer than the length on the front side. For inside corners, the dorsum side of the molding should be equal to the length of the wall you need to embrace, from the corner to the next piece of molding.

3. 3

   Place the pieces. Add together glue to the sides of the molding touching the wall or ceiling (being careful not to add too much) and then fit them into identify. Brand sure both pieces get a nice, smooth fit.^[8]

4. iv

   Nail in place. Once they've been fit into place, nail the molding into the studs, alternating betwixt the top and lesser of the molding. Make sure non to become too shut to any edges, as this can cause not bad.

   Advertisement

Cut Outside Corners Download Commodity

1. 1

   Measure your piece. Measure the distance between the last board finish and the corner. Add together twice the thickness of molding plus an inch or two and cut a piece of molding to this length. Measure and cut pieces for both sides of the corner.^[9]

   • Tip: Cheque the molding against the wall. Dry-fit the molding to the wall and mark the back of the molding as shut equally you can get to the corner. This may exist a more helpful measurement than the i you took. Offset with any measurement is longer, to exist rubber.

2. 2

   Miter the ends. Miter the ends of both corner pieces at a 45° bending, with the long point on the front end or facing side of the molding. This should allow the two corner pieces to fit together.^[10]

   • The length on the front side should at present be longer than the length on the dorsum side.

3. 3

   Place the pieces. Add glue to the sides of the molding touching the wall or ceiling (being conscientious non to add together besides much) and so fit them into place. Make sure both pieces go a dainty, smooth fit.^[11]

4. 4

   Boom in place. Once they've been fit into place, boom the molding into the studs, alternating between the tiptop and bottom of the molding. Brand sure not to get too shut to any edges, as this can cause neat.

   • With outside corner molding, you should also nail through the end of 1 piece into the other, if information technology is thick enough.

   Advertizing

Cutting Rounded Corners Download Commodity

1. 1

   Do your math. Figure out what the measures of the angles will have to be for the pieces. Take the overall bending of the corner y'all need to turn (usually xc°)and split information technology past the number of ends being used to make the turn (thus 45° for a normal corner). If you lot are using three pieces of molding to make the turn, you'll commonly demand to be cutting those at 22.5°.^[12]

2. 2

   Measure, cut, and roughly place the ii side pieces. Cut your side pieces with 22.5° angled ends, so that the shorter, inside betoken ends right where the wall begins to curve. Dry fit the pieces and mark where they cease on the wall with a pencil.

3. 3

   Measure the altitude between them at the base. Measure the altitude been them at their base. This volition be your measurement for the transition piece.

4. four

   Cut your transition slice. Cutting your transition slice with the 22.v° angles on each side, with the long points both on the outside, facing surface of the molding. Err on the side of making the piece to long. You tin also cut it downwards further to get a good fit.

5. v

   Place your transition slice. Identify all of the pieces and glue and nail them as normal.^[13]

6. half-dozen

   Alternatively, make a regular corner and fill the gap. If you don't like the await of a transitional piece, you can make a regular corner and simply plaster the gap that's formed.

   Advertisement

1. 1

   Install door molding. Door and window molding is essentially the same as wall molding, information technology just places the boards in the other direction. Most of the same instructions apply. For doors, proceed in mind that at that place are a number of ways to do the corners. You tin miter them as discussed to a higher place, y'all can apply decorative corner pieces, or you tin construct a lintel. All of these options are probable easier than the mitered corners.^[14]

   • Don't forget to accommodate doors. Brand certain there will not exist whatever overlap.

2. ii

   Install window molding. Windows are much the aforementioned as doors. The main departure for installing molding on windows is that you must be careful of the window frame. Practice not entirely overlap the window frame and brand sure you are simply hammering molding into the studs around the window.^[fifteen]

3. three

   Install base trim. Doing base trim, or the molding at floor level, is by and large the same as installing it anywhere else on a wall. Just be sure to use sparse blocks or skims to account for rug. Y'all don't want to place the molding directly at the subfloor. Also, don't forget about shoe molding. Information technology is installed exactly the same equally wall molding and can make your floor look much cleaner and professional.^[xvi]

4. four

   Install chair or picture rail. Chair and picture rail are the same as wall molding.^[17] But be sure to apply a laser level and measure out constantly to make sure you lot're keeping them directly.

   • Use MDF instead of plywood for chair and motion picture rails since it'southward cheaper and smoother.^[eighteen]

5. v

   Install shadow boxes. Shadow boxes are built much like picture frames. Make certain to lay everything out in pencil earlier yous cut your pieces, try to make every bit many every bit possible the aforementioned size to save time, and make sure you hammer them in at the studs (to avert hitting wires or pipes). For doing odd angles, such as for stairs, only remember the formula we discussed before: take the total angle that needs to exist achieved and divide it by two (for the ii pieces making the turn).^[19]

   Advertizing

Inquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

Video

• If you've never worked with a miter saw earlier, ask for a demonstration at the rental store. Alternatively, there are many videos to exist found online that demonstrate the technique.

• Information technology is much easier to install molding with someone to assistance, especially when installing crown molding.

Advert

• Be careful buying extra long lengths of molding because they often twist and warp. Inspect each piece carefully before accepting them.

• Do not use nails longer than 2 inches (5.1 cm) to nail in the molding. Whatsoever longer nails might hitting pipes or electrical wires.

• Many cities crave that a ruby flag exist tied at the end of any load that extends beyond your vehicle's outside. Check your local ordinances before loading up.^[20]

Advertizement

Things Yous'll Need

• Scaffolding or stride ladders
• Record measure
• Pencil
• Centre protection
• Face up mask
• Molding
• Miter saw
• Paw saw
• Hammer
• Brads
• Finish nails
• Nail setter
• Air hammer
• Compressor and airline
• Caulk
• Painters tape
• Paint or stain

About This Article

Article Summary 10

To install molding, start by cutting the pieces to the right size. Next, locate and mark studs as information technology's best to boom molding into a support construction. When placing the molding, first mucilage the edges that make contact with the wall or ceiling, and then nail the molding into the stud. If you demand to fit your molding effectually corners, cut ii pieces of molding that will fit between the last board terminate and the corner. Make sure to miter the ends of both corner pieces at a 45 degree angle, with the long point on the dorsum side where the molding touches the wall. To acquire how to cut rounded corners for your molding, keep reading!

Did this summary assistance you?

Cheers to all authors for creating a page that has been read 75,358 times.

Did this article help you?

Source: https://www.wikihow.com/Install-Molding

Posted by: archuletainuitch.blogspot.com

Share this post